- Research
- Open access
- Published:
Assessing the efficiency and microbial diversity of H2S-removing biotrickling filters at various pH conditions
Microbial Cell Factories volume 23, Article number: 157 (2024)
Abstract
This study aimed to investigate the operation of three parallel biotrickling filters (BTFs) in removing H2S at different pH conditions (haloalkaliphilic, neutrophilic, and acidophilic) and their associated microbial population in the biodesulfurization process. BTF columns were inoculated with enriched inoculum and experiments were performed by gradually reducing Empty Bed Retention Time (EBRT) and increasing inlet concentration in which the maximum removal efficiency and maximum elimination capacity in EBRT 60 s reached their maximum level in haloalkaline condition (91% and 179.5 g S-H2S m−3 h−1). For visualizing the attached microbial biofilms on pall rings, Scanning Electron Microscopy (SEM) was used and microbial community structure analysis by NGS showed that the most abundant phyla in haBTF, nBTF, and aBTF belong to Gammaproteobacteria, Betaproteobacteria, and Acidithiobacillia, respectively. Shannon and Simpson indexes evaluation showed a lower diversity of bacteria in the aBTF reactor than that of nBTF and haBTF and beta analysis indicated a different composition of bacteria in haBTF compared to the other two filters. These results indicated that the proper performance of BTF under haloalkaliphilic conditions is the most effective way for H2S removal from air pollutants of different industries.
Graphical Abstract
Introduction
Many industrial activities such as wastewater treatment, petrochemical and natural gas refineries, biogas, composting, pulp and paper, and food production discharge a significant amount of volatile sulfur compounds (VSCs) to the environment [1, 2]. The simplest VSC, hydrogen sulfide (H2S), is a colourless, flammable, and potentially explosive, heavier than air, highly poisonous and lethal at 600 ppm, severely corrosive, odour nuisance with rotten egg smell, and a very low odour threshold value [1, 3]. Fossil fuels, the main energy source around the world, contain sulfur compounds that generate oxidated sulfur mixtures during the burning process. These compounds are precursors of acid rain that destroy the natural environments and architecture [4, 5]. Hence, sulfur removal from fuels is necessary and sometimes challenging.
Massive research has been carried out in the field of removing H2S from gaseous fuels and off-gases, but still, new innovative research and new technologies are required to improve the performance of biological technologies and to elucidate the role of microbial communities in their functionality [6,7,8,9].
Traditional physicochemical technologies have been employed for the treatment of gaseous emissions containing VSCs of waste and/or sour gas streams. However, these methods in contrast to biological methods (biodesulfurization) [2, 10], which are based on the oxidation of H2S by sulfide oxidizing bacteria (SOB), are not very environmentally friendly and cost-effective due to high energy consumption for operating at high pressure and temperature [6, 11].
Biodesulfurization processes of gas streams are usually carried out by four types of conventional bioreactors: biofilters, bioscrubbers, biotrickling filters (BTF), and bubble column bioreactors [12,13,14]. Although all of them can effectively remove hydrogen sulfide from contaminated gaseous streams, BTFs have some advantages over others. In BTF aqueous nutrient phase is trickled over the packing bed and the gas phase is forced upward through the vessel. The contaminants are absorbed and biodegraded by the microbes growing on the packing surfaces as biofilm. This technology has been scaled up at industrial scales for the removal of up to 12,000 ppm H2S concentrations [15] and unlike bioscrubber and bubble column bioreactors, the processes of absorption, biodegradation of contaminating compounds, and regeneration occur simultaneously in a single column. In comparison to biofilters, BTFs are more effective in removing compounds that recalcitrant to degradation or generate acidic by-products [16,17,18] and environmental conditions such as humidity, temperature, pH, and discharge of toxic substances can be better controlled. The choice of the type of bioreactor depends on the nature and loading rate of contaminated gases [19,20,21].
In BTFs, the autotrophic Sulfide oxidizing bacteria (SOB) have the primary role in the detoxification of VSCs. Thus, the activity and composition of autotrophic and heterotrophic microbial communities significantly impact the efficiency and removal rate. On the other hand, environmental factors such as pH have a basic role both in the diversity of the microbial community and solubility of sulfidic compounds.
The effects of pH as a critical factor in the formation of bacterial community structures have been emphasized by various researchers including Tu et al. [22], Omri [23], and Chouari [24]. At different pH, varying autotrophic and heterotrophic microbial groups become active and dominant [25]. The selective pressure imposed by environmental conditions such as pH and concentrations of pollutants drastically changes the population structure and its diversity and ultimately affects system performance [26]. The results of Tu's 2017 research also showed that the biofilm thickness and stability are greatly affected by the inlet loading rate and pH [27].
This work aimed to investigate the effect of three different pH-adjusted conditions on the performance and microbial community in three parallel biodesulfurizing BTFs working in the same operational condition. For robust long-term operation, a new method of periodic relative starvation was used to control reactor clogging. Moreover, to elucidate the effect of pH on H2S utilizing bacterial community, the bacterial community composition of BTFs' attached biofilm was studied by next-generation sequencing (NGS) of the 16S rRNA gene. The simultaneous investigation of three BTFs in the same conditions except for pH and the proof of the differences in the consortia population promoting biological removal is the subject that has been less studied in depth.
Results and discussions
BTFs performance in experimental conditions
The results of the E1 experiment (Fig. 1) indicate that haBTF is more efficient in removing H2S than nBTF and aBTF. In this experiment, haBTF reached its maximum EC of 179.8 g m−3 h−1 in less EBRT (50 s) with 91.14% EC, which is 5.44% and 2.94% more efficient than nBTF and aBTF, respectively. The critical EC in which 97% of inlet H2S is removed by the systems was also determined to be 31.1 g m−3 h−1 and 17.5 g m−3 h−1 higher than nBTF and aBTF's EC, respectively.
In the E2 experiment (Fig. 1), the three filters were operated at constant EBRT (60 s), but with rising Ci (from 1000 to 6000 ppm). The results were similar to the E1 experiment, with haBTF reaching the maximum EC of 210.6 g m−3 h−1, which was higher than nBTF and aBTF by 59.8 g m−3 h−1 and 36.3 g m−3 h−1, respectively. The highest critical EC (167.8 g m-3 h-1) was also detected in haBTF. Although haBTF obtained the highest EC rate in the E2 experiment, the RE of the system was recorded at its highest point (91.14%) in the E1 experiment of the same reactor. These results indicate that haBTF is more efficient in removing H2S than the other two reactors. Furthermore, aBTF had a slight advantage over nBTF in both experiments (see Table 1).
In E3 experiments, the effect of reducing EBRT from 120 to 15 s on RE was investigated at three constant and independent input concentrations of 200, 1000, and 2000 ppm of hydrogen sulfide in bioreactors. The results in Figure S1 show that reducing EBRT from 120 to 80 s in haBTF at the three mentioned concentrations has no effect on the reduction of RE, and even when the inlet concentration is 1000 ppm, by reducing the time to 40 s, only 6% of RE is reduced. It has been observed that the removal efficiency reduction curves for haBTF have a lower slope compared to aBTF and nBTF, for all three concentrations. This indicates that the reduction of removal efficiency with the reduction of EBRT in haBTF is slower and independent of the inlet concentration. Based on the results obtained, it can be concluded that aBTF exhibits better performance as compared to nBTF (Table 1).
Based on the outcomes of three experimental conditions, it has been concluded that filters exposed to more stringent pH conditions perform better at a constant inlet concentration. However, when the inlet concentration varies at a constant EBRT, the result is different. In such a case, nBTF performs slightly better than aBTF.
Throughout the experiments, a minimum oxygen-to-sulfide ratio of 25 was maintained. This ensured that there was enough oxygen to completely oxidize the sulfide. Keeping sulfide at a minimum allowed for ideal conditions for complete oxidation to sulfate. This is important because sulfate provides more energy for biomass development than relative oxidation and biosulfur production. However, if the oxygen level is lower than the sulfide level, biosulfur will form and accumulate on the packing bed, causing a pressure drop and potentially blocking the system [28]. Additionally, biofilm formation on the packing media can reduce oxygen penetration, requiring more oxygen supply in aerobic biodegradation systems [18, 29].
Generally, sulfide-to-sulfate oxidation was almost complete during the experiments (more than 88% and 12% of applied sulfide converted to sulfate and biosulfur, respectively). Also, 81–90%, 75–87%, and 78–88% of H2S were removed at alkaline, neutral, and acidic conditions, respectively, and were assessed by measuring the outlet concentration of hydrogen sulfide placed at the first half of the column height, showing that the most of the H2S was removed at this part. Jia et al. Have reported almost the same rate of conversion in their acidic BTF with 89% of H2S converted to S0, but despite higher average biofilm formation in alkaline BTF than in acidic reactor, less H2S conversion (77%) was observed [30]. This disagreement is probably because of the mass transfer limitation which is more acute in haBTF since hydrogen sulfide (H2S) is a weak acid (pKa = 7), it has been observed that the pH level of the MSM solution can influence its ability to transfer mass from gas to liquid phase. However, this effect is less significant at acidic or neutral pH levels. To address this challenge, the present study conducted periodic relative starvation, which resulted in a higher conversion rate of hydrogen sulfide as compared to Jia et al.'s report. This fact is also a reason why a change in retention time will have less impact on mass transfer under alkaline conditions than under acidic or neutral pH levels.
Under conditions of constant hydrogen sulfide concentration and declining EBRT, hydrogen sulfide will transfer more mass than oxygen due to its higher concentration. In the absence of sufficient oxygen content for complete sulfide oxidation, the sulfur-to-sulfate ratio will rise [9]. The ratio of O2:H2S gradually decreases as the input pollution load increases, and with less oxygen present in the recycling medium, the oxidation of HS− is incomplete, leading to an increase in the proportion of elemental sulfur in place of sulfate. On the other hand, a decrease in EBRT reduces gas-to-liquid mass transfer, while an increase in hydrogen sulfide concentration leads to an increase in biosulfur production due to the biological potential limitation in HS− to SO42−. This is the result of a decrease in oxygen content in the recycling medium and incomplete HS− oxidation [31].
Bacterial community diversity analysis
After ending all experiments (90 days), to investigate the correlation of various bacterial populations on the efficiency of H2S removal, an analysis of bacterial community and structure was carried out using three amplicon libraries: haBTF, nBTF, and aBTF. After deleting the wrong identified or low-quality sequences, a total of 160,632 tags (69% of initial) were identified with an average length of 424 bp, which comprised 61,264 tags in the library of haBTF, 50,216 tags in library nBTF and 49,152 tags in library aBTF. The clustering of all tags to OTU was investigated at 97% similarity and the relative abundance data was calculated for each library. A total of 290 bacterial OTUs were obtained from three amplicon libraries and 119, 134, and 37 OTUs were assigned to haBTF, nBTF, and aBTF, respectively. At the phylum level, (data has not been shown) proteobacteria were the most dominant phylum in all samples, so more than 70% of the total read sequences in three BTFs were classified in this taxon. The other most abundant phyla were Bacteroidetes (18%, nBTF) and actinobacteria (30%, aBTF). The relative abundances and population structures of the bacterial communities at the taxonomical class level are shown in Figure S3. In haBTF, the most abundant classes were Alphaproteobacteria and Gammaproteobacteria (20.9% and 73.7%, respectively), in nBTF Alphaproteobacteria, Betaproteobacteria, Gammaproteobacteria and Flavobacteria (3.7, 59.6%, 15% and 16.6%, respectively) were more important and in aBTF sample Acidithiobacillia and Actinobacteria (65.4% and 30.4%, respectively) were the most prevalent classes. In terms of phylogeny, Acidithiobacillia is classified as an independent class of in the Proteobacteria, but previously its type order Acidithiobacillales was classified in the Gammaproteobacteria. The Betaproteobacteria includes the most abundant sulfur-oxidizing bacteria, but it has been reported that in very harsh environmental conditions most SOB belongs to the Gammaproteobacteria [32] and in extremophile acidic conditions, Acidithiobacillia play a key role. Table S1 lists the number of OTUs predicted in the data set per taxon.
The results of molecular studies (Fig. 2) showed that in the alkaline condition of haBTF, the Gamma and Alphaproteobacteria are the most abundant classes (73.7% and 20.9% respectively). In neutral and acidic pH conditions the frequency of these taxa decreased so the abundance of Gammaproteobacteria decreased to 15% and 1.15% and of Alphaproteobacteria to 3.7% and 1.4%, respectively. Under acidic pH conditions, the most abundant classes were Acidithiobacillia and Actinobacteria with 65.4% and 30.4%, respectively. In nBTF, the Betaproteobacteria, Flavobacteria, and Gammaproteobacteria were the most abundant classes, respectively.
In the present study, contrary to the results of Omri et al., [23] and Chouari et al., [24], the lowest ecological diversity was observed at acidic pH, and in accordance with the results of Tu et al. [22], the microbial diversity at neutral pH is higher than that of acidic pH. Acidithiobacillus was the most abundant group of bacteria in the mentioned study which is in agreement with the results of the relative abundance of different bacterial groups in three tested conditions of the present study. As shown in Table 2, Acidithiobacillus and Thiobacillus are the most abundant genera of bacteria in aBTF and nBTF, respectively and haBTF was abundant with unclassified groups of bacteria. The superiority of Acidithiobacillus and Thiobacillus has also been proved in Zhang et al.'s 2022 acidic BTF [33]. In aBTF after the Acidithiobacillus the most abundant acidophilic microorganism is Mycobacterium with an abundance of 27%, which is most likely mixotrophic SOB, and consistent with the results of Jia et al. [34], the abundance of mixotrophic SOB Mycobacterium was 78.4%. in aBTF with extremely acidic conditions.
OTU rank curve
The species diversity of a population depends on two factors: species richness and evenness. Increasing species richness (X-axis) simultaneously with uniform distribution of abundances (Y-axis log scale) can dramatically increase species diversity. OTU rank abundance curve can visually depict two factors at the same time. As can be seen in Fig. 3A in terms of species richness, nBTF has the highest and aBTF has the lowest richness. The steep slope of the OUT curve indicates the lack of uniform distribution of abundance in aBTF so that a limited number of OUTs ranks have the highest frequency and more numbers have the lowest frequency. The curves of haBTF and nBTF, at first start with steep slopes and then vary gently downward parallel, so the two BTFs are similarly distributed in terms of species evenness, and both have more evenness than the aBTF. Overall, according to OTU rank curves, haBTF and nBTF have the same species diversity and more than the aBTF.
Rarefaction curves
Based on observed OTUs with increasing sequencing, it was shown that the three rarefaction curves tend to be smooth. This suggests that the produced data is enough to cover the diversity of all species in the community. The other rarefaction curves based on the Chao1 and ACE values also confirmed these results (Figure S4).
Heat map analysis
Heat map analysis was done based on the relative abundance of each genus in each sample. To minimize the differences degree of the relative abundance value, the values were all log-transformed. The gradation of green shows the relative abundance of the three samples, −3 (light red) being the minimum and 3 (light green) the abundance of maximum considered. As shown in the heat map (Fig. 3B), haBTF contained a more diverse group of bacteria in comparison to the two other reactors. This may be because of the formation of a pH gradient in haBTF which provides an adverse niche for different genera. The pH gradient may also be formed in nBTF but in less adverse value than that of haBTF. The most abundant known genera in aBTF, nBTF, and haBTF were Acidithiobacillus, Thiobacillus, and Rhodobaca, respectively. The effect of pH on the formation of different microbial communities has been reported in previous reports by Chouari et al., [24] and Tu et al., [22] in which they corroborated changing pH from neutral to acidic conditions will cause alteration in microbial population and both insisted on attendance and abundance of Acidithiobacillus in (extremely) acidic biofilters.
Alpha diversity
According to results in Table 3, the value of observed species and indexes of Chao1and ACE showed species richness at neutral pH of nBTF is considerably higher than the others, and also the species richness at the haloalkaline condition (pH 8.5) is higher than the acidic pH (2–3.5). Severe acidic conditions as selective pressure decreased species richness, but despite the relatively high salt concentration and slight alkalinity in haBTF, seemingly these limiting factors had less effect on species richness.
Shannon value (H) and Simpson index (D) estimators can reflect the diversity (richness and evenness species) of the community. Shannon value is influenced more by rare abundant species while the Simpson index (D) is affected by dominant and even species. According to the results of Shannon's value, the community diversity of haBTF is greater than the other samples and aBTF is in the lowest level of diversity, but Simpson's index indicated species diversities of haBTF and nBTF are the same and they are greater than aBTF due to its much less evenness and richness.
OTU PCA analysis
To display the differences in OTU composition in three BTF samples, Principal Component Analysis (PCA) was used to construct a 2-D graph to summarize factors mainly responsible for this difference. Figure 3C, based on principal component analysis, showed that along the PC1 axis, the samples could be divided into two separate groups, and along the PC2 axis, they could be separated into two other groups. The composition of OTUs in haBTF is significantly different from that of aBTF and nBTF, and according to the distribution of aBTF and nBTF along the vertical axis of PC2, it could be concluded that these two populations are more similar in terms of OTU structure. These results showed that the bacterial populations of haBTF have a significant difference compared to the other two BTFs, and on the other hand, the bacterial populations formed in aBTF and nBTF are more similar to each other.
Scanning electron microscopy
Scanning electron micrographs were utilized to track the development of biofilm on pallrings after 90 days of experiments (Fig. 4). The analyses revealed the presence of a complex community of bacteria in the haBTF samples (Fig. 4A and B), including filamentous bacilli that were 1.5 μm in diameter and 4 μm in length, rod-shaped bacteria that were 0.4 μm in diameter and 1 μm in length, and cocobacilli that were 0.5 μm in diameter and 1 μm in length. In addition to bacterial aggregation, biosulfur sediments are shown in Fig. 4B. In nBTF samples (Fig. 4C, D), there are bacteria with diameters ranging from 0.34 to 0.9 μm and lengths ranging from 0.9 to 9 μm, biosulfur accumulations produced by SOB secretions with diameters ranging from 1.4 to 7 μm (pointed with yellow arrows), and a nematode (nearly 5 μm in diameter and 35 μm in length), in addition to various sized bacteria. Even though the experiment used lethal levels of hydrogen sulfide, the existence of nematodes and other protozoa in neutral pH biofilters was unexpected. Amorphous fouling and spherical accumulations of biosulfur (diameter 8–10 μm) were also seen in aBTF-associated biofilm (Fig. 4E, F)).
Upon comparing the images of the three filters, it is evident that haBTF (Fig. 4B) has a thicker and more condensed biofilm layer in which rod-shaped microbial strains were trapped in large amounts of EPS as compared to the acidic and neutral ones. This observation is consistent with the findings of Jia et al., who reported a higher rate of biofilm formation in alkaline BTF than in acidic conditions [30]. It is worth noting that nematodes were only observed in the neutral biofilter. Although this was unexpected due to the presence of lithic concentrations of H2S, it could indicate successful pH control during the experiments. This group of organisms are predators of bacteria and therefore play a vital role in controlling their population [35].
Conclusions
Assessing the effect of pH conditions (haloalkaliphilic, neutrophilic, and acidophilic) on the efficiency of H2S removal in the BTF system, three parallel experiments were performed in which removal-determining parameters showed 91.14% RE and 179.8 gS-H2S m−1 EC in haBTF when EBRT was 60 s. These values differed in nBTF and aBTF with 85.7% and 88.2% RE; 141 and 145 gS-H2S m−1 EC, respectively. These results besides a lower reduction slope of RE (%) in haBTF with a decrease in EBRT compared to nBTF and aBTF demonstrated better performance of haloalkaliphilic BTF in H2S removal. This biofilter had also distinct bacterial diversity in comparison with nBTF and aBTF, as NGS results showed, and its biofilm structure seemed more condensed with higher EPS content based on its SEM images. Despite less bacterial diversity, acidic conditions performed slightly better compared to the neutral system (see Table 4) at a constant inlet concentration, revealing that biotrickling systems with harsh pH conditions perform better in removing H2S than neutral filters.
Materials and methods
Culture media composition
The nutrient solutions of recirculating and enrichment cultures were the mineral salt media (MSM) (Table S2). MSMha, MSMn, and MSMa were used in haloalkaline biotrickling filter (haBTF), neutral biotrickling filter (nBTF), and acidic biotrickling filter (aBTF), respectively. All chemicals were of analytical grade with more than 99.5% purity and were purchased from Merck.
During the enrichment and start-up periods, the sole sulfur source for the SOB growth was supplied by Na2S2O3\(\cdot\)5H2O solution (10 g L−1), and H2S mix gas was used during the acclimatization and the experimental phases.
Enrichment, acclimatization and immobilization of SOB consortia
For acquiring diverse and active microbial sulfur-oxidizing consortia as initial inoculum, the SOB community was enriched from a mixture of the following materials: activated sludge of urban and industrial wastewater treatment plants (petrochemical and leather processing industries). At the beginning of the enrichment process, 350 g of the mixture as mentioned earlier was mixed with 2 L of MSMn and MSMha culture media individually and supplemented with Na2S2O3\(\cdot\)5H2O (10 g L−1) as the sole energy source. Enrichment cultures were continuously aerated for about 6 weeks. The pH values of MSMn, MSMha, and MSMa were automatically controlled at 7, 8.5, and 1.5 to 2 respectively using 0.5 M NaHCO3 (for MSMha) or 2N NaOH (for MSMa and MSMn) when necessary and the temperature was controlled at 30 °C. At this phase, 30% of the culture media was replaced by fresh media every week and the process continued for 6 weeks until the density of the enriched microbial consortium increased to 107–108 CFU ml ml−1. At the immobilization period (startup period), BTFs were inoculated with 500 ml of enriched media harboring 107–108 CFU ml−1 of bacteria. Sodium thiosulfate was replaced by H2S as the sole source of energy and to allow the development of biofilm on the packing media, H2S concentration was gradually increased stepwise from 100 to 2000 ppm over 62 days with an empty bed residence of 120s [35,36,37,38,39].
Biotrickling filter setup
As shown in the schematic drawing of the experimental setup (Fig. 5), three identical lab-scale BTFs were operated to study the performance of H2S removal under haloalkaline, neutral, and acidic conditions. The BTF glass columns had an internal diameter and a height of 8 and 60 cm respectively and were packed with polypropylene 16 mm Pall rings to the height of 50 cm (Pall Ring Company, UK). The column temperature was controlled at 30°C by continuous water circulation in the external jacket (Lauda RC6-CS, Germany). There were three sampling ports in the inlet, outlet, and middle sections of the column. In each BTF, the MSM was fed and recirculated over the packing media by using a peristaltic pump (Watson-Marlow Inc WM603s, USA) through a spray nozzle located at the top of BTFs. The trickling liquid velocity (TLV) During the startup stage was set to 0.9 m h−1 and during all experiments was set to 7 m h−1.
Before recycling culture media to the reactor, the coarse sulfur particles were separated by gravity sedimentation in 200 ml sludge traps. To prevent any release of H2S gas, the outlet gas of BTFs passed through the NaOH trap. The pressure drops of reactors (∆P) due to biofilm growth were monitored with U-tube water manometers connected to the bottom and top sections of the columns. The air supplied by a compressor was filtered and passed through a thermal mass flow controller (MFC) (BROOKS Instruments USA, type 6250s). Nitrogen flow gas (N2, 99.995%) was controlled by Digital MFC) BRONKHORST Instruments Netherlands, type EL-FLOW-201CV. Air and nitrogen were humidified by passing through a water bubble column.
A cylinder of H2S gas (5%, balanced N2) was used for supplying hydrogen sulfide and a Digital MFC (UNIT Instruments USA, type UFC-1661) was used to control the flow of gas. Synthetic polluted air was created by combining H2S with humidified N2 and air mixture, in a mixing chamber and divided equally into three flows using a three-way distributer, the mixed gas flow rate was controlled by rotameters before entering each reactor. The gas current was supplied from the bottom of BTFs through a diffuser and the treated gas discharged from the upper end of the column. During the operation times, to prevent the toxic effects of by-products and supply fresh nutrient sources, 15% of spent liquid media was replaced with fresh MSM daily. The pH of MSMn and MSMa in the nBTF and aBTF were monitored and controlled at set-points of 7 ± 0.1 and 2.5 ± 0.5 respectively by automatic addition of 2 N NaOH by pH controller and dosing pump (Hanna BL 7916, USA). The pH and alkalinity of MSMha in haBTF were adjusted at a value of 8.5 ± 0.1 and 0.4 M, respectively using the addition of make-up fresh medium. If the pH of the MSMha was higher than 8.5, carbon dioxide gas was used to adjust the pH. Compensation for evaporated water in bioreactors was done by adding water weekly. In all designed experiments, the amount of circulating dissolved oxygen (DO) was considered to be higher than the requirement for complete sulfide oxidation. If the DO of the recirculating medium was reduced compared to the saturated state, excess oxygen was purged to the recirculation medium in the MSM reservoir.
To control filters' clogging during operation, a new method of periodic relative starvation was used. This method is based on the observation that the growth of biofilm is higher near the inlet due to the higher concentration of the substrate, making it more prone to clogging and blockage. In such cases, the U-shaped manometer shows the pressure drop. So, to prevent clogging and maintain the activity of the column, the position of the polluted air inlet was changed alternately by moving the input along the length of the column at different time intervals. This allows the substrate to be spread and a biofilm to be formed along the entire length of the column, increasing the length of time the column operates without the need for washing to remove biofilm and sulfur from the bed.
Experimental conditions and methodology
After 62 days of establishing stable conditions in all three bioreactors (E1, E2, and E3), experiments were conducted to evaluate and compare the performance of BTFs. The conditions of conducting these experiments are shown in Table 5. Experiments E1 and E2 were conducted in two periods of 11 days each, while experiment E3 was conducted in a period of 15 days. To evaluate system performance, parameters such as load retention (LR), elimination capacity (EC), and removal efficiency (RE) were calculated by measuring the inlet (Ci) and outlet (Cout) concentrations and using retention time and flow rate (Q). By decreasing the empty bed residence time (EBRT) while keeping (Ci) constant or by increasing (Ci) and keeping EBRT constant, the contamination load of bioreactors can be increased, and the behavior of BTFs can be studied. (see the Eq. (1)) [40]:
where LR is load retention (gS m−3 h−1), Ci is inlet concentration (gS m−3), Q is the flow rate (m3 h−1), Vb is the volume of the packed bed (m3), and EBRT is empty bed retention time (h).
The effects of EBRT on BTF's operation
During the 22-day E1 experiments, the EBRT was gradually reduced from 120 to 20 s while maintaining a constant Ci of 2000 ppm. This resulted in an increase in LR from 82 to 493 g m−3 h−1. To ensure performance stability, each period was maintained for 48 h. Table 5 displays the details of the E1 experiments' conditions. At the end of each stage of EBRT change, inlet and outlet hydrogen sulfide concentrations were measured, and EC and RE values were calculated. Critical parameters such as ECcritical and EBRTcritical were determined at the points where the RE reached 97% [41]. The calculation of maximum EC and critical EBRT can provide valuable information for bioreactor modeling, performance, and design. The third experiment (E3) was conducted in three Ci concentrations (200, 1000, and 2000 ppm) to assess the impact of decreasing EBRT (from 120 to 15s) on removal efficiency (RE). See Table 5 for further experiment conditions.
The effects of inlet concentration on BTF's operation
According to the results obtained in the E1 experiments, in E2 experiments, EBRT was kept constant at 60 s, and Ci was gradually increased from 1000 to 6000 ppm in 22 days (LR 82 to 493 g m−3 h−1). The design of BTFs can benefit from the reduction of EBRT which can lead to a reduction in the height of the column and the initial construction costs. To ensure stable performance, each period of increased LR was continued for 48 h in E1 and E2, and 24 h in E3, refer to Table 5 for detailed test conditions.
Microbial diversity analysis
DNA extraction
At the end of experiments, to evaluate the changes in microbial communities as a function of the BTFs pH values, 30 g of packed bed with attached biomass was collected from top, middle, and bottom sections along the length of the reactors in aseptic condition. Total Genomic DNA was extracted and purified from biomass, using Fast DNA® Spin Kit for Soil (MP Biomedicals, USA) following the manufacturer's instructions, but the binding time of DNA to a silica matrix was modified to 20 min. For each sample, all the above-mentioned operations were performed in triplicate. The quantity and quality of the extracted DNA were analyzed by NanoDrop UV–VIS Spectrophotometer (Thermo Fisher Scientific, NanoDrop ONE, USA). Structural DNA integrity was evaluated by gel electrophoresis analysis (concentration of agarose gel 1%, voltage 150 V, electrophoresis time 40 min).
NGS analysis
DNA samples were sent to Beijing Genomics Institute (BGI, Hong Kong NGS Lab) for bacterial diversity analysis based on BGI protocols. Briefly, DNA sample quality control was done by Qubit Fluorometer, NanoDrop, and gel electrophoresis. Then, three libraries of the V3–V4 hypervariable regions (approximately ~ 460 bp) of 16S rRNA genes amplicon were constructed and qualified. Libraries were pair-end sequenced on a MiSeq System (Illumina, San Diego, CA, USA) using the PE300 (PE301 + 8 + 8 + 301) sequencing strategy. The primers used in the PCR reaction were 341 F(5′-ACTCCTACGGGAGGCAGCAG-3′) and 806 R (5′-GGACTACHVG GGTWTCTAA T-3′) (Report of BGI, Hong Kong, NGS lab).
High-throughput sequence data analysis
Bioinformatic data analysis was conducted by the following software. Paired-end reads with sequencing adapters, N base, poly base, low quality, etc. were filtered out then clean paired-end reads were overlapped and combined to generate the consensus sequences (tags) by FLASH (V1.2.11). The tags were clustered to Operational Taxonomic Unit (OTU) with 97% pairwise identity by UPARSE-OTU algorithm in USEARCH (v7.0.1090). To calculate the abundance of each OTU, the USEARCH global method was used and the representative OTU sequence was selected according to the most abundant sequence of each OTU. Operational taxonomic units representative sequences were taxonomically classified using Ribosomal Database Project (RDP) Classifier v.2.2 trained on the Greengenes database, using 0.8 confidence values as the cutoff.
To analyze and compare the diversity and structure of bacterial communities, alpha diversity indices (Observed species, Ace, Chao1, Shannon, and Simpson) were calculated by Mothur (V1.31.2), and beta-diversity (Principal Component Analysis) was studied using the package ade4 of software R (V3.1.1). OTU's rank curve, rarefaction curves, alpha diversity indexes, and OTU's heat map analysis were done by software R (V3.1.1).
Electron microscopy analysis
Scanning electron microscopy (SEM) images were used for the identification of microbial biofilm formation on the Pall Rings surfaces. The samples were taken from different heights of the BTF column and submerged in ringer solution for removal of planktonic cells. Then samples were fixed for 2 h in an aqueous solution of 2% osmium tetroxide and washed with water and subsequently postfixed with a solution of 2.5% glutaraldehyde in phosphate buffer for 1.5 h at 4 °C and washed in the water again. The graded series of Ethanol solutions (25, 50, 75, 100%) were used for dehydration and finally, the samples were freeze-dried for 1 day. For SEM (ZEISS 960A, Germany) examination, replicas were produced by shadowing with a layer of gold in a sputter coater (Balzers SCD 004, Lichtenstein) [42].
Analytical methods
H2S concentration was monitored online in the sampling port at the inlet, outlet, and middle sections of reactors using electrochemical and photoionization detectors (PID). A portable electrochemical sensor (SP2nd SI-100 SENKO, Korea) was used to measure H2S concentration from 0 to 100 ppm, and at a concentration from 100 to 4000 ppm, a fixed TVOC system contained PID detector (Ion Science, UK) was used. The precision of online sensor measurement was confirmed monthly by gas chromatographic (GC) analysis. The GC instrument was an Agilent Technologies (model 6890N Network GC System, USA) equipped with a flame photometric detector (FPD) and HP-1 capillary column (0.25Ò 3000 mm; Hewlett Packard, USA). The initial, mild, and final oven temperature was 50, 120, and 250 °C, with temperature ramping 5 °C min–1 and 20 °C min–1. Nitrogen was used as the carrier gas at a flow rate of 1.5 ml min−1 and the temperature in the oven, injector, and detector were fixed at 250 °C, 100 °C, and 250 °C, respectively.
The concentration of sulfide and sulfate were measured using ion chromatography (Waters, USA) equipped with an IC-Pak anion HC column (4.6 4.6 × 150 mm; Waters) and a conductivity detector (Waters 432). Eluent consisted of 1.7 mM sodium carbonate and 1.8 mM sodium bicarbonate solution with a flow rate of 0.9 ml min−1. Dissolved oxygen (DO) and pH were monitored online in a liquid medium by (HQ40d, HACH) and (HANNA HI98191, USA), respectively. At the enrichment phase for the enumeration of total culturable chemolithotrophic SOB, samples were taken from the liquid medium, and the standard plate count method was used, dilutions of suspensions were then plated in appropriate MSM agar medium which was supplemented by Na2S2O3\(\cdot\)5H2O 10 g L−1 (Table S2). The plates were incubated at 30 °C and the colonies were counted after 1 month.
Data availability
The datasets generated during and/or analysed during the current study are available from the corresponding author on reasonable request.
References
Guerrero L, et al. Advances in the biological removal of sulphides from aqueous phase in anaerobic processes: a review. Environ Rev. 2016;24:84–100.
Syed M, Soreanu G, Falletta P, Béland M. Removal of hydrogen sulfide from gas streams using biological processes–a review. Can Biosyst Eng. 2006;48:2.
Vikrant K, et al. Biofiltration of hydrogen sulfide: trends and challenges. J Clean Prod. 2018;187:131–47.
Chaiprapat S, Charnnok B, Kantachote D, Sung S. Bio-desulfurization of biogas using acidic biotrickling filter with dissolved oxygen in step feed recirculation. Bioresour Technol. 2015;179:429–35.
Van Leerdam, R. C. v. Anaerobic degradation of methanethiol in a process for Liquefied Petroleum Gas (LPG) biodesulfurization. (2007).
de Rink R, et al. Biologically enhanced hydrogen sulfide absorption from sour gas under haloalkaline conditions. J Hazard Mater. 2020;383:121104.
Roman P, et al. Inhibition of a biological sulfide oxidation under haloalkaline conditions by thiols and diorgano polysulfanes. Water Res. 2016;101:448–56.
Wu H, et al. Recent progress and perspectives in biotrickling filters for VOCs and odorous gases treatment. J Environ Manage. 2018;222:409–19.
Wu J, Jiang X, Jin Z, Yang S, Zhang J. The performance and microbial community in a slightly alkaline biotrickling filter for the removal of high concentration H(2)S from biogas. Chemosphere. 2020;249:126127.
Zytoon MA, AlZahrani AA, Noweir MH, El-Marakby FA. Bioconversion of high concentrations of hydrogen sulfide to elemental sulfur in airlift bioreactor. SciWorld J. 2014;2014:675673.
Cano PI, et al. Life cycle assessment of different physical-chemical and biological technologies for biogas desulfurization in sewage treatment plants. J Clean Prod. 2018;181:663–74.
Allegue B. L., Hinge. J. Biogas upgrading Evaluation of methods for H2S removal. Danish technological institude2014.
de Rink R, et al. Increasing the selectivity for sulfur formation in biological gas desulfurization. Environ Sci Technol. 2019;53:4519–27.
Mudliar S, et al. Bioreactors for treatment of VOCs and odours—a review. J Environ Manage. 2010;91:1039–54.
Khoshnevisan B, Tsapekos P, Alfaro N, Díaz I, Fdz-Polanco M, Rafiee Sh, Angelidaki I. A review on prospects and challenges of biological H2S removal from biogas with focus on biotrickling filtration and microaerobic desulfurization. Biofuel research journal. 2017;4(4):741–50.
Cox, H, Deshusses, M. Combined Removal of H2S and toluene in a single-stage biotrickling filter 2000
Mpanias CJ, Baltzis BC. An experimental and modeling study on the removal of mono-chlorobenzene vapor in biotrickling filters. Biotechnol Bioeng. 1998;59:328–43.
Schiavon M, Ragazzi M, Rada EC, Torretta V. Air pollution control through biotrickling filters: a review considering operational aspects and expected performance. Crit Rev Biotechnol. 2016;36:1143–55.
Giri BS, et al. Review of biotreatment techniques for volatile sulfur compounds with an emphasis on dimethyl sulfide. Process Biochem. 2014;49:1543–54.
Gospodarek M, Rybarczyk P, Szulczyński B, Gębicki J. Comparative evaluation of selected biological methods for the removal of hydrophilic and hydrophobic odorous VOCs from air. Processes. 2019;7(4):187.
Rybarczyk P, Szulczyński B, Gębicki J, Hupka J. Treatment of malodorous air in biotrickling filters: a review. Biochem Eng J. 2019;141:146–62.
Tu X, Li J, Feng R, Sun G, Guo J. Comparison of removal behavior of two biotrickling filters under transient condition and effect of pH on the bacterial communities. PLoS ONE. 2016;11(5):e0155593.
Omri I, Bouallagui H, Aouidi F, Godon JJ, Hamdi M. H2S gas biological removal efficiency and bacterial community diversity in biofilter treating wastewater odor. Bioresour Technol. 2011;102:10202–9.
Chouari R, et al. Microbial analysis and efficiency of biofiltration packing systems for hydrogen sulfide removal from wastewater off gas. Environ Eng Sci. 2015;32:121–8.
Jin Y, Veiga MC, Kennes C. Effects of pH, CO2, and flow pattern on the autotrophic degradation of hydrogen sulfide in a biotrickling filter. Biotechnol Bioeng. 2005;92:462–71.
Soupramanien A, et al. Biological treatment of a mixture of gaseous sulphur reduced compounds: identification of the total bacterial community’s structure. J Chem Technol Biotechnol. 2012;87:817–23.
Tu X, et al. Biofilms formed within the acidic and the neutral biotrickling filters for treating H2S-containing waste gases. RSC Adv. 2017;7:25475–82.
Janssen AJH, Sleyster R, van der Kaa C, Jochemsen A, Bontsema J, Lettinga G. Biological sulphide oxidation in a fed-batch reactor. Biotechnol Bioeng. 1995;47:327–33.
Deshusses MA, Gabriel D. Biotrickling filter technology. In: Shareefdeen Z, Singh A, editors. Biotechnology for odor and air pollution control. Berlin, Heidelberg: Springer; 2005.
Jia T, Zhang L, Zhao Q, Peng Y. The effect of biofilm growth on the sulfur oxidation pathway and the synergy of microorganisms in desulfurization reactors under different pH conditions. J Hazard Mater. 2022;432:128638.
Montebello AM, et al. Simultaneous methylmercaptan and hydrogen sulfide removal in the desulfurization of biogas in aerobic and anoxic biotrickling filters. Chem Eng J. 2012;200–202:237–46.
Montebello AM, et al. Operational aspects, pH transition and microbial shifts of a H2S desulfurizing biotrickling filter with random packing material. Chemosphere. 2013;93:2675–82.
Zhang B, et al. Removal of H2S in an extremely acidic-biotrickling filter: evaluation of removal performance and characterization of microbial communities. J Environ Chem Eng. 2022;10: 108504.
Jia T, Zhang L, Sun S, Zhao Q, Peng Y. Adding organics to enrich mixotrophic sulfur-oxidizing bacteria under extremely acidic conditions—a novel strategy to enhance hydrogen sulfide removal. Sci Total Environ. 2022;854:158768.
Bhat AA, Shakeel A, Waqar S, Handoo ZA, Khan AA. Microbes vs. nematodes: insights into biocontrol through antagonistic organisms to control root-knot nematodes. Plants (Basel). 2023;12(3):451.
Ralebitso-Senior TK, Senior E, Di Felice R, Jarvis K. Waste gas biofiltration: advances and limitations of current approaches in microbiology. Environ Sci Technol. 2012;46:8542–73.
González-Cortés JJ, Torres-Herrera S, Almenglo F, Ramírez M, Cantero D. Hydrogen sulfide removal from biogas and sulfur production by autotrophic denitrification in a gas-lift bioreactor. ACS Sustainable Chem Eng. 2020;8:10480–9.
Duan H, Koe LC, Yan R, Chen X. Biological treatment of H(2)S using pellet activated carbon as a carrier of microorganisms in a biofilter. Water Res. 2006;40:2629–36.
Jiang X, Tay JH. Operational characteristics of efficient co-removal of H2S and NH3 in a horizontal biotrickling filter using exhausted carbon. J Hazard Mater. 2010;176:638–43.
Koe L, Fh Y. A Bioscrubber for hydrogen sulphide removal. Water Sci Technol. 2000;41(6):141–5.
Almenglo F, Ramírez M, Gómez JM, Cantero D. Operational conditions for start-up and nitrate-feeding in an anoxic biotrickling filtration process at pilot scale. Chem Eng J. 2016;285:83–91.
Jia T, Zhang L, Zhao Q, Peng Y. The effect of biofilm growth on the sulfur oxidation pathway and the synergy of microorganisms in desulfurization reactors under different pH conditions. J Hazard Mater. 2022;432:128638.
Bozzola, J. J. Russell, L. D. Electron Microscopy: Principles and Techniques for Biologists. Jones and Bartlett. 1999:49–72
Funding
The funding agencies had no role in the study design, data collection, data analysis, and preparation of the manuscript.
Author information
Authors and Affiliations
Contributions
A.A.R. carried out the experiment; A.A.R. and M.G. wrote the original draft of the manuscript; The work was supervised and designed by M.M.Dand H.M.; and all authors read and approved the final version of the manuscript.
Corresponding authors
Ethics declarations
Ethics approval and consent to participate
Not applicable.
Consent for publication
Not applicable.
Competing interests
The authors declare no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated in a credit line to the data.
About this article
Cite this article
Rouhollahi, A.A., Giyahchi, M., Dastgheib, S.M.M. et al. Assessing the efficiency and microbial diversity of H2S-removing biotrickling filters at various pH conditions. Microb Cell Fact 23, 157 (2024). https://doi.org/10.1186/s12934-024-02427-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s12934-024-02427-9